|
|
|
|
| Main Page > Motley > MicroHouse PC Hardware Library Volume I: Hard Drives |
| Previous | Table of Contents | Next |
ACCULOGIC SIDE-4/PLUS
| Data bus: | 16-bit, ISA |
| Size: | Half-length, full-height card |
| Hard drives supported: | Two IDE(AT) drives |
| Floppy drives supported: | Two 360KB, 720KB, 1.2MB or 1.44MB drives |
| CONNECTIONS | |
|---|---|
| Function | Location |
| 34-pin control cable connector-floppy drive | J1 |
| 4-pin connector-drive active LED | J2 |
| 40-pin AT Interface (IDE) connector | J3 |
| 9-pin serial port 2-internal | J4 |
| 15-pin game port-internal | J5 |
| 9-pin serial port 1-external | J6 |
| 25-pin parallel port-external | J7 |
| USER CONFIGURABLE SETTINGS | ||
|---|---|---|
| Function | Location | Setting |
 I/O Channel Ready signal disabled |
JP4 | open |
| I/O Channel Ready signal enabled | JP4 | closed |
| Floppy drive enabled |
JP5 | pins 1 & 2 closed |
| Floppy drive disabled | JP5 | pins 2 & 3 closed |
| Floppy drive port address is
3F0-3F7h |
JP6 | pins 1 & 2 closed |
| Floppy drive port address is 370-377h | JP6 | pins 2 & 3 closed |
| Single speed floppy drives
supported |
JP7 | pins 1 & 2 closed |
| Dual speed floppy drives supported | JP7 | pins 2 & 3 closed |
| Hard drive enabled |
JP8 | pins 1 & 2 closed |
| Hard drive disabled | JP8 | pins 2 & 3 closed |
| IDE select mode enabled |
JP9 | pins 1 & 2 closed |
| Not used | JP9 | open |
| Hard drive port address is 1F0-1F7h |
JP10 | pins 1 & 2 closed |
| Hard drive port address is 170-177h | JP10 | pins 2 & 3 closed |
| Not used |
JP11 | open |
| IRQ14 normal |
JP12 | pins 1 & 2 closed |
| IRQ14 delayed until ACTIVE signal is removed | JP12 | pins 2 & 3 closed |
| SERIAL & PARALLEL PORT CONFIGURATIONS | ||
|---|---|---|
| Function | Location | Setting |
| Serial port 1 (CN6) enabled |
JP13 | pins 1 & 2 closed |
| Serial port 1 (CN6) disabled | JP13 | pins 2 & 3 closed |
| Serial port 1 (CN6) set to COM1 |
JP14 | pins 1 & 2 closed |
| Serial port 1 (CN6) set to COM3 | JP14 | pins 2 & 3 closed |
| Serial port 2 (CN4) enabled |
JP15 | pins 1 & 2 closed |
| Serial port 2 (CN4) disabled | JP15 | pins 2 & 3 closed |
| Serial port 2 (CN4) set to COM2 |
JP16 | pins 1 & 2 closed |
| Serial port 2 (CN4) set to COM4 | JP16 | pins 2 & 3 closed |
| Parallel port (CN7) enabled |
JP17 | pins 1 & 2 closed |
| Parallel port (CN7) disabled | JP17 | pins 2 & 3 closed |
| Parallel port (CN7) address is LPT1 |
JP18 | pins 1 & 2 closed |
| Parallel port (CN7) address is LPT2 | JP18 | pins 2 & 3 closed |
| Previous | Table of Contents | Next |
